You walk across the living room and notice it. The edges of the boards are rising, and the middle of each plank sits a little lower, like a washboard. Maybe it showed up after your AC acted up, or after a slow leak you didn’t know about. Either way, the question in your head is probably the same one: can I just sand this flat?
In Orlando, that’s the move that most often turns a fixable floor into a harder one. Here’s how to tell what you’re looking at, what to do first, and when it makes sense to call someone who works with hardwood every day.
Cupped, Crowned, Or Buckled: What’s Happening To Your Floor
Cupping is when the edges of a board sit higher than its center. It happens when the underside of the board holds more moisture than the top, so the bottom swells and the plank curls up at the sides. Crowning is the opposite, with the center higher than the edges. Buckling is a different animal altogether: boards lifting away from the subfloor, sometimes in a visible hump.
Most people call all of it “warped,” but the shape tells us a lot. A cupped floor is usually a moisture story. A crowned floor is often a cupped floor that got sanded too early. A buckled floor points to a bigger moisture event, or to boards that had no room to expand.
Why Sanding Cupped Hardwood Too Soon Backfires
While a cupped floor is still damp, the boards are swollen on the bottom. A sander cuts the raised edges flat, and the floor looks great for a few weeks. Then the moisture finally leaves, the boards relax, and the edges you sanded away end up lower than the middle. That’s crowning, and it can show up six months to a year after a too-early sanding.
Sanding a wet board also crushes the grain and can lock the shape in permanently. So the order matters.
First the moisture source gets found and stopped. Then we take moisture meter readings in several spots and compare them against a part of the floor that’s behaving normally. Hardwood inside a conditioned home generally sits around 6 to 9 percent moisture content, and indoor humidity is best kept between 30 and 50 percent. Until the boards are back in that range, sanding is a gamble.
How long does that take? Some say moderate cupping settles in two to three weeks once moisture is under control, and others say weeks or even months. That’s why we don’t go by the calendar. The meter decides.
Orlando adds its own twist. If an AC unit has been down, or a house has sat closed up while the owners were away, the floor soaks up moisture and then dries unevenly once the air is conditioned again. A quote that says “we’ll sand it flat on Thursday” without a single moisture reading behind it should make you pause.
Moisture Without Puddles: Why Orlando Floors Cup When You Can’t See Water
Because moisture doesn’t need a puddle. A dishwasher line, a refrigerator ice-maker, a water heater, or an upstairs bathroom can drip into a subfloor for weeks before anything shows on the surface. By the time the boards lift, the water has been at it for a while.
Then there’s what’s under the house. Plenty of Florida homes sit on concrete slabs, and moisture can wick up through concrete with no standing water at all. Boards lifting along exterior walls are one clue. This is also why engineered hardwood is often recommended over slabs, although solid hardwood can work with the right moisture control.
Older neighborhoods add another layer. In College Park, Lake Eola Heights, and Thornton Park, many homes still have their original hardwood, and original subfloor construction can carry more moisture than a newer build. The same goes for Winter Park homes near the chain of lakes. When we inspect a floor, we look at the wood species, the existing finish, the condition of the planks, and the moisture level in the subfloor, because the answer is rarely in just one place.
Sometimes it really is more than one cause. A slab that holds moisture, a long humid stretch, and an AC that cycles off while you’re traveling can all push on the same floor. We’d rather spend the time finding out than guess and have you pay for the job twice.
Wood Floor Water Damage Repair In Orlando, FL: Who Do You Call First?
If water is still coming in, call your plumber first. If a burst line or a storm has left the floor wet, a water restoration company can start the drying, and your insurance company should hear about it early. Take photos before anything gets thrown away.
We come in for the wood. We repair and replace water-damaged hardwood, but we don’t do water extraction or structural drying, so we’ll tell you straight when someone else needs to go first. One rule of thumb from restoration guidance is that if fans haven’t improved the cupping or the odor after 48 to 72 hours, it’s time for professional drying equipment.
Once the water is handled and the floor has settled, that’s when the hardwood questions start.
Can Water-Damaged Hardwood Be Saved, Or Do The Boards Have To Go?
Often they can be saved, as long as the water has stopped and the floor gets time to dry. Mild cupping with the moisture source fixed tends to flatten out, and once the readings come back normal, a sand and refinish can finish the job.
Some damage can’t be sanded away. When boards have delaminated, meaning the layers have started to separate, sanding won’t bring them back. Mold changes the plan too, and it has to be dealt with before anyone touches the floor. Deep warping, or boards that stay buckled after everything has dried, point toward replacement, and sometimes toward a look at the subfloor underneath.
What most people dread is the next part. If you pull boards, will the floor look patched forever? It doesn’t have to. One homeowner wrote in a Google review that we removed the water-damaged flooring in her guest room and installed new wood, weaving it seamlessly into the adjoining hallway. Other contractors had wanted a transition piece at the doorway, which she didn’t want. We blend new boards into the floor around them and match the stain and finish so the room reads as one floor. Customers mention that stain matching often, including a recent review about a staircase, handrail, and newel post.
That matters when the floor is original. If you own a College Park bungalow or a Lake Eola Heights Craftsman and only a few boards are bad, you shouldn’t have to replace the whole room to fix them. Because we handle the repair, sanding, stain, and finish ourselves, the job stays with one crew from the first board to the last coat.
Cupped Hardwood Floor Questions Orlando Homeowners Ask Most
Will it flatten on its own? Mild cupping can, once the moisture source is fixed. If the leak is still dripping or the slab is still wicking, it won’t, and a repair won’t hold either.
What does it cost to fix? We don’t publish prices, because the number depends on the cause, how far the damage spreads, and whether the answer is sanding, board replacement, or subfloor work. National averages from HomeAdvisor put cupping repair at up to $8 per square foot, a plumbing leak fix at about $150 to $350, and replacing a section of hardwood at $600 to $5,000. Those aren’t our prices, but they show why fixing the source first usually costs less than replacing a floor twice.
Is humidity alone to blame in Orlando, FL? It can be, especially when the AC isn’t keeping indoor humidity in that 30 to 50 percent range. More often it’s humidity plus something else, like a slow leak or moisture coming up through the slab, both common issues in older Orlando neighborhoods.
Is solid hardwood a bad idea in Florida? No, but it needs the right moisture control and a sound subfloor. Over a concrete slab, engineered hardwood is often the safer call.
Does insurance cover it? That depends on the cause and your policy, so photograph the damage and call your insurer before you throw anything out. We can’t speak for your policy.
Do you work outside Orlando itself? Yes. We serve Orange and Seminole counties, including Winter Park.
Fix Cupped Hardwood Floors The Right Way In Orlando, FL
The short version: figure out where the moisture is coming from, stop it, let the numbers come back to normal, and only then decide whether the floor needs patience, a sanding, or new boards. Skip that order and you risk trading cupping for crowning.
At Harrington Hardwood Floors, we’ve worked only with hardwood since 1990. Our owner, Geste Harms, does the work himself, so the person who looks at your floor is the person who fixes it. If your boards are lifting and you’re not sure what you’re looking at, call us at 407-701-2028. We’ll come take a look at the floor and take a moisture reading, and then we’ll tell you honestly what it needs.
